Baja Designs Lights for Off-Road Trucks
Visit
the
Baja Designs Section in the KLM Store for our full line of Baja
Designs Lights.
 HID
bulbs are a quantum leap forward in off-road lighting. HID (high intensity
discharge) lamps produce daylight quality light and brightness, far
outperforming conventional quartz halogen lighting systems. These bulbs are the
same ones being used by BMW, Mercedes and Lexus in their OEM headlights.
A single HID. bulb produces the equivalent of 250 watts of halogen lighting
power while only consuming 50 watts of power and generating far less heat. They
also do not use a filament; they fire an 18,000-volt electric charge between two
electrodes encased in a xenon gas-filled bulb. Since the bulb has no filament,
vibration is not a detriment to its operating life (2000 hours). All this makes
HID Bulbs a perfect fit for off-road use.
HID kits adapt an HID bulb to your existing stock or after-market motorcycle,
truck, or buggy halogen headlight, The kits consists of a high voltage ballast,
HID bulb with built in ignitor, connectors, a simple wiring harness, mounting
hardware and detailed installation instructions. The ballast is fully waterproof
and epoxy encapsulated to stand up to weather and off-road abuse. The ballast
provides the power needed to run the HID bulb, weighs 5 ounces and measures
3-1/2" x 2-3/4" x 1-1/4"
HID electronics kits allow remote mounting of the ballast from the bulb
giving you greater flexibility for installing the system on a motorcycle. The
Ballast can be mounted in such places as the light's fairing, behind a side
panel, or anywhere else as long as it is within 31 inches of the headlight
(Different length high voltage leads available).
For off road truck and buggy mounting, Baja Designs has placed all these
components in one easy to install housing. So what you get is a Single 8 or a
2, 3, 4, 5, or 6 light bar that is ready to be installed the second it is
removed from the box. By eliminating the need to mount an external ballast, your
installation time is cut in half and there is no vehicle down time.
Baja Designs Lighting Advantages:
- No tool quick adjust feature
- Three point vibration isolated mounting system once adjusted lights
stay adjusted
- Optics designed for a smooth useful off-road pattern
- Different focal points for HID and Halogen
- Quick Mount, No tool installation of lighting systems
- Light weight Generation 5 HID ballast (5 ozs) and bulb fully integrated
- Designed by experienced off-road racers who also happen to be engineers
Click the following links for specific Baja Design Lighting
Products:
More information about Baja Design Lighting
Theory
NEW! CALL US TO ORDER!
Wire
Your Light Bar!
To further simplify your
Modular Light Bar installation, we offer a universal
wiring harness kit and two power "splitter" kits. The
wiring harness is designed specifically for routing
power to the top of your vehicle. The Splitter Kits plug
directly into the wiring harness allowing you to switch
any number of lights in any configuration you choose
(switches not provided.) Each light comes with 10" of
wire cable from the back. See the example below.
 Wiring
Harness Kit
8 extension with 2 power and 2
ground leads using sealed weather-pack connectors
1 end left un-terminated for
routing through tubing
Wire terminals and tube
grommets provided
14 gauge wire to handle high
current loads
Detailed installation
instructions included
2 & 3 Way Splitter Kits
Splits one
harness power lead into two or three
Plugs directly
into Wiring Harness Kit (above) using sealed
weather-pack connectors
Offset
connector lengths
14 gauge wire
to handle high current loads
If you build a 5
light bar as shown above and would like to switch the
two "A" lights separately from the three "B" lights. You
will need:
1 Wiring Harness
Kit - Runs power to the
light bar.
1 2-Way Splitter
Kit - Joins one of the
two connectors from the Wiring Harness Kit to the "A"
lights.
1 3-Way Splitter
Kit - Joins the
remaining connector from the Wiring Harness Kit to the
"B" lights.
SAMPLE LIGHT BARS
Shown below are
three sample light bars along with the kits that go into
building them. The lights must be purchased separately.
There are many lens, bulb, and color options available.
Give us a call to order or visit our online store to buy
lights and accessoreis.
 Parts
List
Parts List
2 Fuego Ring Kits
3 Spacer Kits
1 Mount Kit (Clamp-on
Shown)
 Parts
List
1 Mount Kit (Clamp-on
Shown)
MORE LIGHT BAR IDEAS
|
